Compatible Audio & Video Equipment Style | Professional Audio Equipment |
---|---|
Brand Name | HAXNFIELEC |
Certification | NONE |
Origin | Mainland China |
Working Voltage | DC 12V |
Working Current | Above 100mA |
Operational Amplifier OP AMP Tester For Single Dual OPAMP TL071 TL072 TL081/082
58.80 $
400 in stock
Operational Amplifier OP AMP Tester
For Single Dual OPAMP TL071 TL072 TL081/082
Notice:
This board is only for people with professional electronic knowledge, we do not provide operation guidance and technical support. Beginners please do not buy! !
From September 27, 2021, the PCB changed to black color.
Application:
Single op amp and dual op amp screening circuit board, the circuit board can judge whether the IC can be used for amplification, and can roughly judge the conversion rate of the chip at the same time. Can find out those low-speed chips that pretend to be high-speed chips.
Working Voltage:
DC 12V
Working Current:
Above 100mA
Principle Introduction:
IC1a in the circuit is connected to a multivibrator with a frequency of about 1Hz, and the OP Amp. to be tested is connected to a unity gain inverting amplifier working state.
IC2 is an EX-OR gate, and its truth table is that the output is 1 when the two inputs are inverted.
Therefore:
If OP Amp. is normal, points A and B of IC2 must be reversed, so C is 1, and it is still 1 after IC1b and 1d, so the yellow LED D3 lights up;
If the OP Amp. output is open, the point C of IC2 must always be 0, and it becomes 1 after IC1c, so that the red LED D4 lights up.
If the internal short circuit of OP Amp. makes the output voltage fixed to positive or negative, the output of IC1c is also a 1Hz low frequency square wave, and the red and yellow LEDs will flash alternately.
For chips with a low conversion rate, the status indicated by the LED is always yellow, and red will flicker faintly. This can also be used to roughly judge the conversion rate of the chip. Because most of the second-hand chips on the market use low conversion rate instead of high rate, it can also judge whether the chip is counterfeit or not.
The actual test of low conversion rate chips such as: OP07, LM741, the yellow light is always on, the red light is slightly bright.
The actual test of high conversion rate chips such as: TL071, NE5534, MC34071 and other chips, the yellow light is always on, the red light is off.
Single op amp model: LM741, LF356, NE5534, TL071, TL081, OP07 and other standard package single op amp.
Dual op amp model: LM358, NE5532, TL072, TL082, MC1458, RC4558, OP275, AD827 and other standard package dual op amps.
Packing List:
1pcs x Operational Amplifier Tester
Więcej podobnych produktów od innych sprzedawców
- Sale!
TTGO ESP32 LoRa 240Mhz Wireless Module WiFi BT Development Board 1.14 Inch LCD Control Board With T-Display for Arduino
94735 ESP Module TTGO T-Display ESP32 WiFi BT Module Development Board For Arduino 1.14 Inch LCD Control Board Development Board Features: 1. 32-bit low-power dual-core CPU for application processors Up to 240 MHz of main frequency 600 DMPS computing power. 2. Built-in 520 kb SRAM, 4 meters external psram. 3. Supports interfaces such as UART / SPI / I2C / PWM / ADC / DAC. 4. Support ov 2640 and ov 767 cameras, built-in flash wifi image support up TF card support. 5. Multi-mode support Pink lwip and freedos integrated sta [...]
72.63 $ Add to cart - Sale!
YX-Q01 220V Two-Way Power Automatic Switcher 10A 2 Power Supply 2 In 1 Out Power Failure Conversion Switch Board Module
85-240V 10A Dual AC Power Supply Automatic Switching Controller Module Board for dual AC power automatic switching module. The module can automatically switch between the two power sources.Feature:1. AC power2. Dual power input3. Automatic power switch4. Main power YX-Q01Main power supply voltage: 85V~240V ACBackup power supply voltage: 85V~240V ACLoad current: 10A MAXWorking temperature: -25℃~+85℃Working humidity: 5~95 RHSize: 70 x 48 x 18.5mmTip:1. When the main power supply is out of power, the module automatically switches to the backup power supply; when the main power supply is restored, the module automatically switches to the main power supply.2. At [...]
47.26 $ Add to cart - Sale!
3D Printer Parts Suitable For 3D Printer Sidewinders X1 X2 And Pro USB Adapter Board 3D Printer Parts Accessories
Description: This Motherboard Adapter Board is especially for Sidewinders X1 X2 Pro. It is an accessory for 3D printers and is a good choice if your printer happens to be missing it.Specification: Name: Motherboard Adapter BoardWeight: about 10gPackage size: about 8 x 8 x 1cm/3.1 x 3.1 x 0.4in packed in a transparent bagApplicable models: For Sidewinders X1/X2//ProPacking List: Rattlesnake x 1Motherboard adapter board x 1Note: Due to the lighting effects and shooting angles, there is a color difference in the product, please understand.Due to manual measurement, there is [...]
44.73 $ Add to cart - Sale!
Original New Logic Board Kit for RUNTK 5538TP ZA ZB ZZ RUNTK 5351TP 0055FV RUNTK5351TP ZZ RUNTK5351TP ZA
If you are not sure about the model of the board, please send us a clear picture of the original board. Have a nice day!!Welcome to my store,Please contact me if you meet any question,I will try my best to satisfy you. We specialized in T-con board and other electronic products. We have own factory and a large number of T-con boards to sell, please contact me what model you want and I will give you the best price. [...]
47.51 $ Add to cart - Sale!
UNI-T Infrared Thermal Imager UTi120S PCB Circuit Industrial Testing Floor Heating Tube Testing original genuine Thermal camera
Features ● infrared resolution: 120 × ninety● temperature measurement range: - 20 ~ 400 ℃● temperature measurement mode: center point, high and low temperature tracking● photo storage: 16GB TF Card● high and low temperature alarm: image, beep, LED flashing● laser indication / LED lighting● three prevention design: IP54 / two meter fall prevention● PC analysis software● six palette options● adjustable emissivity● the service time shall not be less than 9 hours● 3.7v/2600mah rechargeable lithium battery● bottom design ¼ Screw holes can be used with tripod Uti120s detailed description 1. WORLDWIDE SHIPPING.Except some countries and APO/FPO2. Orders processed timely after [...]
282.00 $ Add to cart - Sale!
IP2368 Bidirectional 100W Fast Charging Module Buck-Boost Type-C Interface Lithium Battery Power Fast Charging Board
body { font-size: 75; color: #000; font-family: Open line-height: 1.3; } dl { margin: 0px; width: 480px; float: left; } dt { width: 100px; height: 15px; float: left; } dd { width: 240px; height: 15px; float: left; } dl dt { margin: 0px; line-height: 22px; color: #474747; font-size: 14px; font-family: tahoma; } #product-desc { width: 100; height: 209px; } #description { width: 100; height: 50; [...]
64.20 $ Add to cart - Sale!
YAOGREENHAM jumbospot V1.3 MMDVM_HS_Dual_Hat Duplex Hotspot Board kit With USB Port Support P25 DMR YSF NXDN For Raspberry pi
New arrival :If you want to buy the finished MMDVM hotspot power bank ,please click this link The default bit error rate is less than 5, and the default offset is 0. If the bit error rate is more than 5, as long as the signal can be received, it can be corrected by offset. 1.Latest version V1.3, and the firmware is latest 2. original cystal : Original from USA Duplex variant of MMDVM_HS_Hat This PCB uses the MMDVM_HS . It has two ADF7021 onboard and allows for duplex operation with two [...]
85.70 $ Add to cart - Sale!
TP5100 Charging Circuit Board 4.2V 8.4V Dual Single Lion Battery Charger Module
Description: 1. The TP5100 is a switching step-down dual section 8.4v/single section 4.2v lithium battery charging management chip. Its QFN16 subcompact package and simple peripheral circuits make the TP5100 ideal for high-current charging management applications in portable devices. 2. Meanwhile,TP5100 has built-in input overcurrent, undervoltage protection, chip overtemperature protection, short-circuit protection, battery temperature monitoring and battery reverse connection protection. 3. The TP5100 has a wide input voltage of 5v-18v, and the battery charging is divided into three stages: trickle precharging, constant current and constant voltage. [...]
40.70 $ Add to cart - Sale!
TP5100 2A Charging Board Power Module Single Dual Battery Charging Management
Description: 1. The TP5100 is a switching step-down dual section 8.4v/single section 4.2v lithium battery charging management chip. Its QFN16 subcompact package and simple peripheral circuits make the TP5100 ideal for high-current charging management applications in portable devices. 2. Meanwhile,TP5100 has built-in input overcurrent, undervoltage protection, chip overtemperature protection, short-circuit protection, battery temperature monitoring and battery reverse connection protection. 3. The TP5100 has a wide input voltage of 5v-18v, and the battery charging is divided into three stages: trickle precharging, constant current and constant voltage. The [...]
40.74 $ Add to cart - Sale!
5A 90W PWM Motor Speed Controller Module DC 5V-35V Adjustable Voltage Regulator Governor Switch
5A 90W PWM Motor Speed Controller Module DC 5V-35V Adjustable Voltage Regulator Governor Switch Specification: Working Voltage: DC 5V-35V Output Current: 0-5A Output Power: 90W Large Quiescent Current: 7μA Standby State PWM Duty Cycle: 1-100 PWM Frequency: 20KHz Product Size: 50 X 30 X 15mm/1.97 X 1.18 X 0.59 Note: 1. Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you! 2. Please allow 1-3mm measuring deviation due to manual measurement. 1 X PWM [...]
40.79 $ Add to cart
Reviews
There are no reviews yet.